JustPaste
HomeCategoriesAboutDonateContactTerms of UsePrivacy Policy
JustPaste

Free online notepad — write and share instantly

Navigate

  • Home
  • Timeline
  • Categories

Info

  • About
  • Donate
  • Contact

Legal

  • Terms of Use
  • Privacy Policy

© 2026 JustPaste.app. All rights reserved.

Made with ♥ by JustPaste

Is a 5 Bar Reinforced PE Air Hose Enough for Your Plant? | JustPaste.app
about 6 hours ago1 views
💻Technology

Is a 5 Bar Reinforced PE Air Hose Enough for Your Plant?

A Compressor Room in Pune, Last March


The pressure gauge attached to the receiver showed 7bar while at the other end of the line the operator was only receiving around 4bar and his impact wrench kept stopping mid-way while he tried loosening the bolts. The reason i was present at site was that the manager of the factory purchased around 100 meters of 5bar reinforced industrial PE air hose and wondered whether he had made the right choice or not and maybe yes , too early to judge. Atleast this pipe seems good , looks nice and flexible and clean coiled against the wall but this wasnt his first issue with the compressor, previously his maintenance lead had complained twice about the compressor . The compressor was perfectly fine however.

5 Bar Polyester Reinforced Industrial PE Air Hose on a Real Line

Forty metres, that was the run from the receiver to the bay. We hung a second gauge at the far end and watched it through a morning shift. The receiver sat at 7 bar. At the wrench, with three tools running, it dropped to something like 4.2. No leaks anywhere. The bore was 8 mm and he had two tools sharing one whip. The air was squeezing through a pipe too thin for the job.

He’d picked the 5 bar hose off a price list, since it was cheapest per metre and the shop said 5 was plenty. I told him over chai that his receiver ran at 7. A hose rated for 5 on a 7 bar line lives on borrowed time, worse in May when the shed climbs past forty degrees and the PE softens. I’ve seen one let go at a coupler near the end of a double shift. It whipped across a pallet and hit nobody, luckily, though it took a drum label with it.

What fit his line in the end was a 10 mm bore hose with a higher working figure, and a second whip so the tools stopped fighting. The 5 bar polyester reinforced stuff went to the compressor bay for blowing dust off benches at low pressure, where it’s perfectly happy. Cheap fix, and the wrench stopped stalling by Friday. Roughly eleven thousand rupees on the reorder, I think, against the downtime he’d been losing.

The Pressure Rating Mistake Buyers Keep Making

A textile mill near Coimbatore bought the cheaper of two quotes last monsoon. By October the cover had cracked where the hose rubbed a steel rack. Nobody had asked what the working pressure was. Price per metre decided it. I’ve sat in that meeting more than once, and the cheaper quote wins every time the compressor gets all the attention. I did it myself on an early job, sizing the plant around the compressor and picking hose last off a catalogue page.

A packaging unit in Noida sent a whole batch of whips back inside a week, every one failed at the same collar. The hose was fine. The crimp had been done by eye, and the barb simply walked out under pressure. We redid them with a proper ferrule and a crimp to a stated diameter, forty minutes a lot, and the line ran clean for months afterwards.

Reels, Lengths and Air Hose Reel Manufacturers in India

Near Ludhiana, in a fabrication yard, I pulled apart a reel where the inner coils had flattened from heat and nobody had noticed for a season. Going through a few air hose reel manufacturers in India, I found the spring tension and the swivel matter more than the paint, and the hose inside matters more than either. For the tube inside a reel I usually point people to this range of air tubing and pneumatic pipe, then ask for the longest reach they actually need before anything else.

A dairy plant outside Meerut left its wash-down reels in direct sun all May. By June the PE had gone tacky and kinked at the first bend. They moved the reels under a shed roof and fitted a guide roller at the exit, and the same hose lasted another year.

Fifteen metres sounds generous until the bay is twenty wide and the operator needs the far corner. I once watched a man wedge a stretched reel in a doorway and lean on it for an hour. The retraction spring went by lunch. For most mid-size sheds I’d go with twenty metres on a 10 mm bore. A press shop with heavy tooling might want less, because the weight drags.

What I’d Put on the Next Order

On the next order I’d pull the working pressure off the receiver plate and paint it on the wall by the drop. Low pressure blowing duty, benches and dust, is where I’d still happily use the 5 bar polyester reinforced industrial PE air hose. On a 7 bar line I’d leave it on the shelf. I did the sums once for a bottling line, something like three rupees a metre extra against a burst every second month.

Back in Pune the manager did something I liked. He went down the line with a marker pen and wrote the working pressure on every coil that came off the truck. His storekeeper grumbled for a week. Then a new hire pulled the wrong coil off the rack. He read the number and put it back without asking anyone. When he reorders now he goes through TIS Nexus with the receiver figure already typed on the request, bore and reach beside it. The last coil I saw in his bay still had the number on it in black pen.


← Back to timeline